Dvg 1120s manual

The interface displays a single prompt character Typing a question mark after the Please note that all characters must be entered in lower case. All command line examples in this chapter are in bold type. Listed below are some of the most commonly used commands, parameter s , and examples of their usage.

General Setup Commands nwdbg system reboot Definition: This command is used to restart the device. Parameter s : None. Example: nwdbg system reboot. Example: nwdbg save changes. Example: nwdbg factory reset. If only nwdbg ip is typed, this command shows the IP configuration. Manual: While the system is booting, the system uses a fixed IP address. If only nwdbg mask is typed, this command shows the IP configuration.

If only nwdbg gw is typed, this command shows the IP configuration. If only nwdbg tftp is typed, this command shows the download link. Parameter s : [disable enable] Example: nwdbg dns disable. The image must be resident on that TFTP server. The image is downloaded for storage in DRAM. Erase Runtime Flash Memory Program Runtime Flash Memory Done OK. In this section you will learn how to establish a network at home or work, using Microsoft Windows XP.

Click Next In the following window, select the best description of your computer. Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next.

Format the disk if you wish, and click Next. To continue click Next. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network.

After run- ning the Network Setup Disk on all your computers, your new wireless net- work will be ready to use.

You may enter a Com- puter Description if you wish; this field is optional. All computers on your network must have the same Workgroup name. To check on the IP Address of the adapter, please do the following:. Right-click on the Local Area Connection icon in the task bar.

Input your IP address and subnet mask. The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of The subnet mask must be the same for all the computers on the network. IP Address: e. Select Use the following DNS server addresses. A window similar to this one will appear.

Type ping xxx. A good wireless connection will show four replies from the Wireless Router or Access Point, as shown. A window similar to this will appear. A good wireless connection will show four replies from the wireless router or access point, as shown.

Dimensions: 6. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. Possessions or Protectorates, U.

The replacement Hardware need not be new or have an identical make, model or part. D-Link may in its sole discretion replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent or superior in all material respects to the defective Hardware.

Repaired or replacement Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.

D-Link further warrants that, during the Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software.

Software will be warranted for the remainder of the original Warranty Period from the date or original retail purchase. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non- conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software and all copies thereof is first returned to D-Link.

The license granted respecting any Software for which a refund is given automatically terminates. Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:. Do not include any manuals or accessories in the shipping package.

D-Link will only replace the defective portion of the Product and will not ship back any accessories. Make the connection as follows:. Obtain suitable cabling for the connection. Set the console to use the following communication parameters for your terminal:. Most of the screens are identical, whether accessed from the console port or from a Telnet interface. If your terminal or terminal emulation program is properly configured according to the specifications defined above, you will see the POST test and the boot up process.

After the process is completed, you will see the window shown be- low. The following window will be displayed. Shown Below. This The following window will appear. To access the console mode, you must first make sure the console is con- nected to the Diagnostics port and the appropriate cabling for the connection is being used.

Please see the previous section for additional information. Next, power the de- vice on by simply plugging it in. You will see the boot up process. After the process is complete, you will see the window shown below:. The following window will be displayed:. Shown below. The The following window will appear:.

The firmware upgrade procedure is complete. The interface displays a single prompt character Typing a question mark after the Please note that all characters must be entered in lower case. All command line examples in this chapter are in bold type. Listed below are some of the most commonly used commands, parameter s , and examples of their usage.

General Setup Commands nwdbg system reboot Definition: This command is used to restart the device. Parameter s : None. Example: nwdbg system reboot. Example: nwdbg save changes. Example: nwdbg factory reset. If only nwdbg ip is typed, this command shows the IP configuration. Manual: While the system is booting, the system uses a fixed IP address.

If only nwdbg mask is typed, this command shows the IP configuration. If only nwdbg gw is typed, this command shows the IP configuration. If only nwdbg tftp is typed, this command shows the download link. Parameter s : [disable enable] Example: nwdbg dns disable. The image must be resident on that TFTP server. The image is downloaded for storage in DRAM. Erase Runtime Flash Memory Program Runtime Flash Memory Done OK. In this section you will learn how to establish a network at home or work, using Microsoft Windows XP.

Click Next In the following window, select the best description of your computer. Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer.

This may take a few minutes. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Format the disk if you wish, and click Next. To continue click Next. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network.

After run- ning the Network Setup Disk on all your computers, your new wireless net- work will be ready to use. You may enter a Com- puter Description if you wish; this field is optional. All computers on your network must have the same Workgroup name. To check on the IP Address of the adapter, please do the following:. Right-click on the Local Area Connection icon in the task bar. Input your IP address and subnet mask. The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of The subnet mask must be the same for all the computers on the network.

IP Address: e. Select Use the following DNS server addresses. A window similar to this one will appear. Type ping xxx. A good wireless connection will show four replies from the Wireless Router or Access Point, as shown.

A window similar to this will appear. Next at the nwdbg prompt type, "tftp" to get a list of tftp commands. You should now have an S I have done dozens of these and this always works perfectly.

I have lots of these all over running FWD, Voipcheap, etc. They have standout call audio quality. A couple of things though: First off, they will not work through a firewall. Second, the unit will not work well with very high speed connections. It will slow them down. It's good with speeds up to about 7 mbps, but when I run it as a router on my 10 mbps Roadrunner cable, it slows it down to about 7 mbps. One other thing-the two lines can not be used with separate VOIP providers.

It can even call one line from the other well. If you just upgraded a box to S and are not getting dial tone on the ports then you most likely have not done a Factory reset I finally learned this on my second box. When the first dialed digits match the table, the system will store all the digits and forward them to the non-default line. A full telephone number, e.

Click the Edit icon on the window above to access the second IP Filter window, shown below: 2nd IP Filter window After you have clicked on an edit icon, this Pass or Block- Pass or Block the action defined in this filter rule. Direction - Select In or Out to pass or block packets coming in or going out of the network. Filter Rule State - Enable or disable the filter rule as defined in the menu Click on the Save button at the bottom right of the window to save the settings. Subnet Mask - Type in an appropriate subnet mask that allows the static route to function.

The only difference is that a particular IP Address can be assigned to a particular host. Click on Save to save the settings.

Each entry, in this configuration, can be used to map multiple, contiguous global addresses and local addresses to each other. Monitor - Ethernet Statistics Rx Packets- total number of packets received by Rx Overrun Packets - The number of packets received that exceed the octet maximum length imposed on Ethernet packets.

Overrun packets are generated by some proprietary software applications. Tx Packets - The total number of valid packets transmitted by the device since Page 34 Web-based Management continued Factory Reset Before performing a Factory Reset, be absolutely certain that this is what you want to do.

The console must be connected to the Diagnostics port. Most of the screens are identical, whether accessed from the console port or from a Telnet interface. To access the console mode, you must first make sure the console is con- nected to the Diagnostics port and the appropriate cabling for the connection is being used.

Example: nwdbg save changes nwdbg factory reset Definition: This command is used to set the DVGS back to its default settings and then restart the device. Parameter s : None. Example: nwdbg factory reset